FMI W32DS User Manual download pdf

Note: Gather all mantel pieces together before assembling

mantel.

WARNING: Only use 1

/4" screws in pocket holes to

assemble mantel. Damage to mantel will result if other

screws are used for this purpose.

WARNING: Use only 1/2" or 3/4" screws with brack-

ets in hardware pack 118983-01. Damage to mantel will

result if other screws are used for this purpose.

ASSEMBLING MANTEL

IMPORTANT: More than one person is required to lift

assembled mantel. Lift mantel by leg assemblies. Lifting

by header or mantel top could damage mantel.

1. For leg assembly, lay side or front that does not contain

pocket holes front side down on a soft surface. Pocket

hole locations will vary by model. Pay special attention

to the up direction arrows on panels.

2. Position second panel as shown in Figure 1, page 2. Align

panels at bottom. With one person holding the panel align-

ment secure, attach panels using 1

" screws through

pocket holes. Check assembly for correct alignment.

3. Repeat steps 1 and 2 for second leg assembly.

4. Each leg assembly will use 3 brackets for stability. Your

bracket hardware kit will contain either 1/2" or 3/4" screws.

Using two 1/2" or 3/4" screws, install a bracket in the center

of each leg assembly and one at each end within 1" of but

not over the last pocket hole (see Figure 2, page 2).

WS26DS, W32DS and W36DS

Wall Mantel and Base with Trim

ASSEMBLY AND INSTALLATION INSTRUCTIONS

IMPORTANT: Read entire instruction sheet before

assembling or installing mantel kit.

These mantels are only approved for use with any

DESA Heating Products compact replace system.

Do not use mantel with any other product.

This mantel kit contains the following:

• Mantel pieces - unassembled and marked as follows:

Base #1 Left Side #4 with arrow

Right Side #2 with arrow Left Front Leg #5 with arrow

Right Front Leg #3 with arrow Header #6 with arrow

Top #7

• Hardware Package (117197-01)

• Bracket Hardware Kit (118983-01)

• Trim Kit 113140-02 (26"), 113140-01 (32") or

113140-14 (36")

• Trim Kit Hardware (102866-01)

The hardware kit 117197-01 contains the following:

• 28 - 1

⁄

" Screws

• 2 - 3" Screws

Tools required:

• #2 Phillips drill bit (3

" min. length)

• Slotted screw driver • Drill Driver

• Measuring Tape • Pencil

If any wood pieces are missing or damaged, contact the

dealer where you purchased this mantel for replacement.

If hardware or trim is missing or damaged, contact DESA

Heating Products at 1-866-672-6040 for referral informa-

tion. You can also visit DESA Heating Products' technical service

web site at www.desatech.com.

Firebox

Perimeter

Trim Included

With This

Mantel

www.desatech.com

1 2 3 4

Summary of Contents

Page 1 - WS26DS, W32DS and W36DS

Note: Gather all mantel pieces together before assembling mantel. WARNING: Only use 1 1/4" screws in pocket holes to assemble mantel. Damag

Page 2 - ATTACHING TOP OF MANTEL

www.desatech.com119360-01B2Left Side Leg AssemblyRight Side Leg AssemblyHeaderFigure 3 - Installing Header5. Position header between leg assemblies

Page 3 - FIREPLACE INSTALLATION

www.desatech.com 119360-01B3Figure 7 - Assembling Trim ASSEMBLING TRIM 1. Remove packaging from three pieces of trim. 2. Locate two adjusting pla

Page 4 - NOT A UPC

119360-01Rev. B07/06119360 012701 Industrial DriveP.O. Box 90004Bowling Green, KY 42102-9004Technical Service and Parts1-866-672-6040NOT A UPC6. Fire

Comments to this Manuals

No comments

FMI W32DS User Manual

Browse online or download User Manual for Fireplaces FMI W32DS. FMI W32DS User's Manual [en]

Summary of Contents

Comments to this Manuals

Related products and manuals for Fireplaces FMI W32DS